Kenwood Transceiver CAT Interface products and fall into the following categories:

  • Kenwood USB CAT interfaces to allow remote control of your transceiver via your PC.  
  • Kenwood USB CAT and audio interfaces giving full access to modes such as PSK31

The CAT cables are compatible with a huge range of Kenwood Equipment. See the individual product descriptions to check which interface is right for your transceiver.  

You will need 
suitable software such as Ham Radio Deluxe, MixW, N1MM and many more that allow the interface to connected via your PC's USB port. If you are uncertain as to software compatibility, use the Contact Us page and we will be more than happy to advise.

The USB interfaces are powered from the the USB bus and will be compatible so long as your software supports the transceiver.

I accept payment via major Credit and Debit Cards and by Paypal. When you purchase products and check-out, you will be taken to a Paypal payments page where you may choose to pay by credit/debit card or by Paypal.



Digimode-1-Kenwood

Product: Digimode-1-Kenwood


USB CAT Control and Audio Interfacing of your Kenwood Transceiver allowing you to fully utilise software such as Ham Radio Deluxe, Echolink, PSK31, DM780, N1MM Logger, MixW and many more.


Complete plug-and-play solution. The interface is full wired for your PC and transceiver. Just follow the instructions to download the FTDI drviers, configure up your CAT/Digimode software and you are up and running.

The Tx/Rx audio signals are galvanically isolated by Bourns 600:600 Ohm transformers and the hardware PTT is opto-isolated. The USB section of the interface uses the highly reliable FTDI Chipset and provides a virtual comm port allowing full CAT control and hardare PTT keying over the RTS signal. 


With this interface, you will be up and running on PSK31, Echolink, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes. 


Cable length is 1.8m from the USB and audio connectors to the interface box. The cables from the interface box to the transceiver is 0.6m. The box is very compact at 80x40x20mm making it ideal to hide away behind the PC or transceiver using no desk space.
 


Kenwood Transceivers either have a combinations of CAT and Data connectors. Use the Options drop down menu to select the cable you need.



Option 1


TS-450s, TS-690s, TS-790s, TS-850s, TS-950s.


* Also suitable for the following Kenwood transcivers where optional chips are installed.
TS-140s and TS-680s (Require the IF-10C)


Option 2


TS-570, TS-590, TS-870, TS-990, TS-2000


Option 3


TS-480 (uses 6 Pin mini-din acc connector)


Option 4


TS-440, TS-940


TS-440 (requires the IC-10 for CAT control)
TS-940 (requires the IF-10B for CAT control)



$66
(+ postage: $12)
Quantity: Options:


Digimode-2-Kenwood

Product: Digimode-2-Kenwood


Digital mode interface giving you fully Isolated Audio Interfacing of your Kenwood Transceiver allowing you to fully utilise software such as FLdigi, Echolink, PSK31, DM780, N1MM Logger, MixW and many more.


Complete plug-and-play solution. The interface is fully wired for your PC and transceiver. Just follow the instructions to download the FTDI drviers, configure up your Digimode software and you are up and running on PSK31 and many more AFSK modes.

The Tx/Rx audio signals are galvanically isolated by Bourns 600:600 Ohm transformers and the hardware PTT is opto-isolated. The USB section of the interface uses the highly reliable FTDI Chipset and provides a virtual comm port allowing hardare PTT keying over the RTS signal. 


With this interface, you will be up and running on PSK31, Echolink, SSTV, Pactor, Packet or any mode that requires  Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes. 


Cable length is 1.8m from the USB and audio connectors to the interface box. The cables from the interface box to the transceiver is 0.5m. The box is very small at 40x35x20mm making it ideal to hide away behind the PC or transceiver using no desk space.


Kenwood Transceivers either have a combination of Data connectors. Use the Options drop down menu to select the cable you need.



Option 1


TS-140s, TS-450s, TS-570, TS-590, TS-670, TS-680s, TS-690s, TS-711, TS-790s, TS-811, TS-850s, TS-870, TS-950s, TS-990, TS-2000


Option 2


TS-480 (uses 6 Pin mini-din acc connector)


Option 3


TS-440, TS-940 (PTT to pin 13 of the acc connector)

$50
(+ postage: $12)
Quantity: Options:


Kenwood USB CAT TS-Cable-1-USB

 


Product: Kenwood CAT TS-Cable-1-USB


Kenwood USB CAT Interface Cable using the highly reliable FTDI Chipset.  The interface is a fraction of the price of the Kenwood IF232 interface and gives you the same functionality in a simple cable solution. 

Full CAT control with PTT on these tranceivers with no modification


TS-450s, TS-690s, TS-790s, TS-850s, TS-950s.


 


* Also suitable for the following Kenwood transcivers where optional chips are installed.
TS-140s and TS-680s (Require the IF-10C)
TS-940 (requires the IF-10B)
TS-711A and TS-811A (require the IF-10A)
TS-440s and R-5000 (require the IC-10)



* The standard cable length is 1.8m.

$30
(+ postage: $8)
Quantity: Options:


Kenwood CAT and PSK Interface TS-Cable-1-Kit-USB

Product:  Kenwood CAT and PSK Interface TS-Cable-1-Kit-USB


The interface offers full USB CAT Control and Audio Interfacing of your Kenwood Transceiver allowing you to fully utilise software such as Ham Radio Deluxe, PSK31, DM780, N1MM Logger, MixW and many more.The USB CAT part of the interface uses the highly reliable FTDI Chipset. With this interface, you will be up and running on PSK31, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes. 


Cable length is 1.8m.


Compatible with the following Kenwood transceivers


TS-450s, TS-690s, TS-790s, TS-850s, TS-950s.


* Also suitable for the following Kenwood transcivers where optional chips are installed.
TS-140s and TS-680s (Require the IF-10C)
TS-940 (requires the IF-10B)

TS-440s (requires the IC-10)

$42
(+ postage: $8)
Quantity: Options:

Kenwood USB CAT TS-Cable-5-USB

Product: Kenwood CAT TS-Cable-5-USB


Kenwood USB CAT Interface Cable using the highly reliable FTDI Chipset.  The interface connects between the USB port of your PC and the DB-9 RS232 port on your Kenwood Transceiver. 

Full CAT control these tranceivers


TS-480, TS-570, TS-590, TS-870, TS-990 and TS-2000



* The standard cable length is 1.8m.

$32
(+ postage: $8)
Quantity: Options:

Make payments with PayPal - it's fast, free and secure!