Icom CAT control and Digital mode interfaces to use software such as Ham Radio Deluxe, FLDigi, WSJT-X to operate PSK31, FT-8, JT9, JT-65, Echolink and many other AFSK modes.
We offer a large range of interfaces to ensure maximum compatibility with modern and older PCs and digimode software. You can also choose to use your PCs internal sound card to generate/decode your Digimode signals or to use an external sound card interface to free up your PCs sound card for normal use. We use icons shown below to guide you to the best choice for your equipment setup.
 |
Suitable for any AFSK and Digital mode such as FT8, JT9, PSK31, WSPR ect. Perfect for use with WSJT-X, FlDigi, Ham Radio Deluxe (DM780), Echolink and many others. Please note that some of these applications offer enhanced functionality when you also have CAT control of the radio. |
 |
The interface has a built in external USB Sound Card based on C-Media CM108 chip. This frees up your PCs internal sound card for normal windows functions. The interface has a built in PTT function and can be used without a CAT interface. |
 |
The interface gives you CAT control of your transceiver via a built in USB Comm port. CAT control allows you to set/get the frequency and mode of your transceiver. The interface used the highly reliable FTDI UART comm port chipset. |
Digimode-4-Icom $100.00
 |
|
| |
USB CAT Control and Audio Interfacing of your Icom Transceiver allowing you to fully utilise software such as WSJT-X, FLDigi, Ham Radio Deluxe, Echolink, PSK31, DM780, N1MM Logger, MixW and many more.
Our Latest Digimode-4 interface provides a single USB connection to your PC and has both built-in USB CAT control and its own built-in USB Sound Card. The interface allows you to dedicate your digital mode working to the external sound card and its independent level setting controls leaving your PCs internal card for normal Windows functions.
This interface is fully wired for your PC and transceiver. Just follow the provided instructions to download the FTDI drivers. The in-built sound card drivers are included in your operating system and the interface will pop up as a generic USB PnP Sound Device. The interface plugs into a free USB port on your PC and to your transceiver CAT and Data/PKT ports. PTT keying is via the interfaces built-in USB comm port RTS signal or you can choose to PTT over the CAT commands if your transceiver supports this.
The Tx/Rx audio signals are galvanically isolated by Bourns 600:600 Ohm transformers and the hardware PTT is opto-isolated.
With this interface, you will be up and running on FT8, PSK31, Echolink, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC and Radio within minutes.
Cable length is 1.5m from the USB port on your PC to the interface box. The cables from the interface box to the transceiver is 0.6m. The box is very compact at 80x40x20mm making it ideal to hide away behind the PC or transceiver using no desk space.
The Digimode-4 PDF instruction manual is here:
http://www.xggcomms.com/userimages/USB-Digimode-4.pdf
Icom Transceivers either have an 8 pin or 13 pin Din accessory connector. Use the Connector Type drop-down menu to select the interface you need.
Radios with the 8 Pin DIN accessory connector
IC-275, IC-375, IC-575, IC-707, IC-725, IC-726, IC-728, IC-729, IC-735, IC-736, IC-737, IC-738, IC-746 (All Versions), IC-756 (All Versions), IC-761, IC-765, IC-775, IC-775DSP, IC-781, IC-820, IC-821, IC-910, IC-7400, IC-7600, IC-7610, IC-7700, IC-7850.
Radios with the 13 Pin DIN accessory connector
IC-78, IC-703, IC-706 (All Versions), IC-718, IC-7000, IC-7100, IC-7200, IC-7300, IC-7410, IC-9100.
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Digimode-1-Icom $70.00
 |
|
| |
USB CAT Control and Audio Interfacing of your Icom Transceiver allowing you to fully utilise software such as WSJT-X, FLDigi, Ham Radio Deluxe, Echolink, PSK31, DM780, N1MM Logger, MixW and many more.
Complete plug-and-play solution. The interface is full wired for your PC and transceiver. Just follow the instructions to download the FTDI drviers, configure up your CAT/Digimode software and you are up and running. The interface plugs into a free USB port on your PC to provide the CAT and PTT keying and to your PCs own Sound Card. At the radio end, it plugs into the CAT and Data ports.
The Tx/Rx audio signals are galvanically isolated by Bourns 600:600 Ohm transformers and the hardware PTT is opto-isolated. The USB section of the interface uses the highly reliable FTDI Chipset and provides a virtual comm port allowing full CAT control and hardare PTT keying over the RTS signal.
With this interface, you will be up and running on FT8, PSK31, Echolink, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes.
Cable length is 1.5m from the USB and audio connectors to the interface box. The cables from the interface box to the transceiver is 0.6m. The box is very compact at 80x40x20mm making it ideal to hide away behind the PC or transceiver using no desk space.
The Digimode-1 PDF instruction manual is here:
http://www.xggcomms.com/userimages/USB-Digimode-1.pdf
Icom Transceivers either have an 8 pin or 13 pin Din accesory connector. Use the Connector Type drop-down menu to select the interface you need.
Radios with the 8 Pin DIN accessory connector
IC-275, IC-375, IC-575, IC-707, IC-725, IC-726, IC-728, IC-729, IC-735, IC-736, IC-737, IC-738, IC-746 (All Versions), IC-756 (All Versions), IC-761, IC-765, IC-775, IC-775DSP, IC-781, IC-820, IC-821, IC-910, IC-7400, IC-7600, IC-7610, IC-7700, IC-7850
Radios with the 13 Pin DIN accessory connector
IC-78, IC-703, IC-706 (All Versions), IC-718, IC-7000, IC-7100, IC-7200, IC-7300, IC-7410, IC-9100.
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Digimode-2-Icom $50.00
 |
|
Fully isolated audio interfacing of your transceiver allowing you to fully utilise software such as Ham Radio Deluxe (DM780), WSJT-X, FLDigi allowing you to operate many digital modes such as PSK31, FT8, JT9, JT65 and Echolink.
Complete plug-and-play solution. The interface is fully wired for your PC and transceiver. Just follow the instructions to download the FTDI drivers, configure up your Digimode software and you are up and running in no time. The interface utilises a free USB port on your PC to provide a comm port to allow for PTT keying via the RTS signal. The interface plugs into your PCs own sound card. At the radio side, the interface plugs into the Data socket for Tx/Rx audio and PTT.
The Tx/Rx audio signals are galvanically isolated by Bourns 600:600 Ohm transformers and the hardware PTT is opto-isolated. The USB section of the interface uses the highly reliable FTDI Chipset and provides a virtual comm port allowing hardare PTT keying over the RTS signal.
Cable length is 1.5m from the USB and audio connectors to the interface box. The cables from the interface box to the transceiver is 0.5m. The box is very small at 40x35x20mm making it ideal to hide away behind the PC or transceiver using no desk space.
The Digimode-2 PDF instruction manual is here:
http://xggcomms.com/userimages/USB-Digimode-2.pdf
Icom Transceivers either have an 8 pin or 13 pin Din accesory connector. Use the Connector Type drop-down menu to select the interface you need.
Radios with the 8 Pin DIN accessory connector
IC-275, IC-375, IC-575, IC-707, IC-725, IC-726, IC-728, IC-729, IC-735, IC-736, IC-737, IC-738, IC-746 (All Versions), IC-756 (All Versions), IC-761, IC-765, IC-775, IC-775DSP, IC-781, IC-820, IC-821, IC-910, IC-7400, IC-7600, IC-7610, IC-7700, IC-7850
Radios with the 13 Pin DIN accessory connector
IC-78, IC-703, IC-706 (All Versions), IC-718, IC-7000, IC-7100, IC-7200, IC-7300, IC-7410, IC-9100.
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Digimode-3-Icom $70.00
 |
|
|
External USB Sound Card isolated audio interface allowing you to operate many AFSK digital modes such as PSK31, FT8, JT9, JT65 and Echolink. Fully plug and play. Simply plug the USB cable into your PC and the Data plug into your transceiver.
Perfect with digital mode applications such as DM780, WSJT, FLDigi, Echolink etc.
The interface uses the C-Media CM108 USB Audio Chipset and most modern operating systems already have the driver pre-installed. The advantage of this interface is your PCs normal soundcard is not tied up for Digital mode operations. As you now have a separate and dedicated soundcard for your Digital Mode working, you can independently set the Tx/Rx audio levels leaving normal PC sound unaffected.
The interface is fully galvanically isolated between PC and Radio. The Tx/Rx audio signals are isolated by Bourns 600:600 Ohm transformers and the hardware PTT is opto-isolated. The PTT is keyed by an internal VOX circuit in the interface.
Cable length is 1.5m from the USB and audio connectors to the interface box. The cables from the interface box to the transceiver is 0.6m. The box is very compact at 80x40x20mm making it ideal to hide away behind the PC or transceiver using no desk space.
The Digimode-3 PDF instruction manual is here:
http://xggcomms.com/userimages/USB-Digimode-3.pdf
Radios with the 8 Pin DIN accessory connector
IC-275, IC-375, IC-575, IC-707, IC-725, IC-726, IC-728, IC-729, IC-735, IC-736, IC-737, IC-738, IC-746 (All Versions), IC-756 (All Versions), IC-761, IC-765, IC-775, IC-775DSP, IC-781, IC-820, IC-821, IC-910, IC-7600, IC-7610, IC-7700, IC-7850
Radios with the 13 Pin DIN accessory connector
IC-78, IC-703, IC-706 (All Versions), IC-718, IC-7000, IC-7100, IC-7200, IC-7300, IC-7410, IC-9100.
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Icom IC-Cable-7-USB-ISO $55.00
 |
|
|
The interface offers full USB CAT Control and 600:600 Ohm transformer isolated audio interfacing of your Icom Transceiver allowing you to fully utilise software such as Ham Radio Deluxe, PSK31, DM780, N1MM Logger, MixW and many more.
The USB CAT part of the interface uses the highly reliable FTDI Chipset. The audio cable uses high quality Bourns 600:600 Ohm transformers to galvanically isolate the audio circuits to reduce the chance of ground loops and induced mains hum and is terminated in the 8 pin Din Accessory connector. See the radio compatibility list below.
With this interface, you will be up and running on PSK31, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes.
Full CAT control with PTT and Isolated TX/Rx Audio on these Icom tranceivers.
IC-746, IC-746 Pro, IC-756 Pro, IC-756 Pro 2, IC-756 Pro3, IC-910H, IC-7400, IC-7600, IC-7610, IC-7700, IC-7800, IC-7850
* The standard cable length is 1.8m
Add Tracked Shipping (Not for USA customers)
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Icom IC-Cable-8-USB-ISO $55.00
|
|
|
The interface offers full USB CAT Control and 600:600 Ohm transformer isolated audio interfacing of your Icom Transceiver allowing you to fully utilise software such as Ham Radio Deluxe, PSK31, DM780, N1MM Logger, MixW and many more.
The USB CAT part of the interface uses the highly reliable FTDI Chipset. The audio cable uses high quality Bourns 600:600 Ohm transformers to galvanically isolate the audio circuits to reduce the chance of ground loops and induced mains hum and is terminated in the 13 pin Din Accessory connector. See the radio compatibility list below.
With this interface, you will be up and running on PSK31, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes.
Full CAT control with PTT and Isolated TX/Rx Audio on these Icom tranceivers.
IC-703, IC-7000, IC-7100, IC-7200, IC-7300, IC-7410, IC-9100
* The standard cable length is 1.8m
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Icom IC-Cable-7-USB $45.00
 |
|
|
The interface offers full USB CAT Control and Audio Interfacing of your Icom Transceiver allowing you to fully utilise software such as Ham Radio Deluxe, PSK31, DM780, N1MM Logger, MixW and many more. The USB CAT part of the interface uses the highly reliable FTDI Chipset. With this interface, you will be up and running on PSK31, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes.
Full CAT control with PTT and TX/Rx Audio on these Icom tranceivers.
IC-746, IC-746 Pro, IC-756 Pro, IC-756 Pro 2, IC-756 Pro3, IC-910H, IC-7400, IC-7600, IC-7610, IC-7700, IC-7800, IC-7850
* The standard cable length is 1.8m
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Icom IC-Cable-8-USB $45.00
|
|
|
The interface offers full USB CAT Control and Audio Interfacing of your Icom Transceiver allowing you to fully utilise software such as Ham Radio Deluxe, PSK31, DM780, N1MM Logger, MixW and many more. The USB CAT part of the interface uses the highly reliable FTDI Chipset. With this interface, you will be up and running on PSK31, SSTV, Pactor, Packet or any mode that requires CAT control and Tx/Rx Audio Interfacing between your PC Soundcard and Radio within minutes.
Full CAT control with PTT and TX/Rx Audio on these Icom tranceivers.
IC-703, IC-7000, IC-7100, IC-7200, IC-7300, IC-7410, IC-9100
* The standard cable length is 1.8m
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.
Icom IC-Cable-1-USB $33.00
 |
|
|
CAT control on ANY Icom transceiver but with additional CAT PTT contol on the transceivers below
IC-703, IC-7000, IC-7100, IC-7200, IC-7300, IC-7410, IC-7600, IC-7610, IC-7700, IC-746 (All versions), IC-756 (All versions), IC-7800, IC-7850, IC-R10, IC-R7000, IC-R7100, IC-R72, IC-R75, IC-R8500 and IC-R9000.
* The standard cable length is 1.8m.
Add Tracked Shipping
If you wish to upgrade to tracked shipping on your item then you can choose to add it to your Shopping Cart here. You just need to add it once and the cost is $5. If you are in the USA, do not add this option. We already use a tracked USPS shipment to The USA.